01
Plating-ready surface control
Specify No. 8 / 600 grit mirror, brushed or other agreed finishes for components that will be chrome plated, PVD finished or used as visible hardware.
Bathroom hardware tubing
Stainless Steel Tubes for Bathroom Hardware & Sanitary Fittings
Stainless steel tubing for shower columns, towel rails, grab bars and faucet components—specified around surface finish, dimensional fit and fabrication requirements.
- No. 8 / 600 grit mirror and brushed finish options
- 304 and 316L material options for project requirements
- Support for cutting, punching, bending and protective packing
Three buyer priorities
Surface, fit and forming requirements discussed before quotation
02
Tube-in-tube dimensional fit
For adjustable shower columns, OD/ID and inner-weld-bead requirements can be reviewed with your matching tube, drawing or sample.
03
Forming for spouts and arms
Discuss bend radius, surface expectations and downstream fabrication so tube material and finish are selected for the intended component process.
Tube Options & Finishes
Tube profiles for visible bathroom hardware components
Quote support is available for standard or project-specific dimensions. Please provide shape, material, OD or section size, wall thickness, length, finish, quantity and any processing drawing.
Round Tubes
Common for shower columns, towel rails, grab bars and faucet arms. Tube-in-tube combinations can be assessed for telescopic systems.
Square & Rectangular Tubes
Suitable for contemporary rail, rack and fitting assemblies where flat faces or controlled orientation are required.
Surface Finish Options
No. 8 / 600 grit mirror, brushed and other agreed finishes. Surface protection and packing should be defined for visible parts.
Quality requirements
Inspection points to confirm on an RFQ
| Requirement | How it is addressed | RFQ information to provide |
|---|---|---|
| Visible surface | No. 8 / 600 grit mirror or brushed finish can be specified for bathroom hardware components. | Finish sample, visual standard, plating or PVD route. |
| Tube-in-tube fit | OD/ID tolerance and inner weld-bead treatment can be reviewed for sliding assemblies. | Both mating tube sizes, target clearance and sample if available. |
| Straightness | Straightness <1.0 mm/m may be requested where it is relevant to the component assembly. | Length, inspection method and acceptance requirement. |
| Forming | Bend radius, ovality and surface condition should be agreed before production. | Drawing, bend geometry and post-forming finish requirement. |
| Protection | Protective packing may be specified to reduce handling marks during internal logistics and export shipment. | Individual wrap, bundle method, carton or pallet requirement. |
Applications
Tubing for bathroom hardware assemblies
Towel Racks
Round tube components with surface finish, cut length and joining requirements matched to the assembly.
Shower Columns
Mirror or brushed visible tubes, with dimensional fit options for adjustable tube-in-tube structures.
Bathroom Grab Bars
Tube supply for component fabricators; wall thickness, bend geometry and project requirements are confirmed by RFQ.
Processing Services
Prepare tubes for your next production step
Fabrication support
Where specified, tube supply can be prepared for component manufacturing requirements.
- Cut-to-length supply
- Hole punching and drilling locations
- End forming and deburring requirements
- Bend preparation and agreed protective packing
304 vs 316L
304 is commonly considered for indoor bathroom hardware where the environment and finishing route are defined by the buyer.
316L can be considered for more demanding chloride or coastal exposure conditions when the complete component environment supports that choice.
Salt-spray reference values of 48 h for 304 and 96 h for 316L should be treated as RFQ-specific test conditions, not a blanket product guarantee.
Production & Inspection
Ten visible steps from coil receiving to final loading
The sequence below is retained in full for buyer reference. Actual controls, records and acceptance criteria should be agreed for the relevant order.
STEP 01
Raw Material Receiving
STEP 02
Strip Rolling & Annealing
STEP 03
Precision Strip Slitting
STEP 04
Tube Welding
STEP 05
Nitrogen Protection
STEP 06
Online Infrared Inspection
STEP 07
Dimensional Monitoring
STEP 08
Mirror Polishing
STEP 09
Protective Packaging
STEP 10
Final Inspection & Loading
FAQ
Questions from bathroom hardware buyers
Can the tubes be supplied for chrome plating or PVD finishing?
We can discuss a No. 8 / 600 grit mirror surface and the visual acceptance standard needed before your finishing process. Please confirm the plating route, sample or surface reference during RFQ review.
Can you support telescopic shower-column tube combinations?
Yes. Provide both tube sizes, target fit, length and inner-weld-bead requirement. A matching sample or assembly drawing helps define the dimensional discussion.
Which material should be considered: 304 or 316L?
Material choice depends on the end environment, finishing route and project specification. 304 and 316L can be quoted; confirm any test method and acceptance condition in advance.
Can cutting, punching and protective packing be included?
These requirements can be reviewed with a drawing, hole positions, cut lengths, quantity and required packaging method. Confirming them before quotation reduces downstream handling changes.
Send your bathroom hardware tube requirement
Share a drawing, tube size, material, finish, quantity and processing needs. We will review the information needed for a clear manufacturing-focused quotation.